Microsoft Network Client version 3.0 for MS-DOS Release Notes ------------------------------------------------------------- This document contains information about Microsoft(R) Network Client version 3.0 for MS-DOS(R) that wasn't available when the "Windows NT (TM) Server Installation Guide" version 3.51 was printed. Contents -------- 1. Installing Network Client 2. Setup PATH Problem With Microsoft Windows 3. If You Have an 8088 Processor 4. Setup Requires 429K Available Memory 5. Setup is Slow on Some Computers 6. Network Client Cannot Be Set Up on DoubleDisk Drive 7. Windows 3.x Setup Network Choice 8. If COMMAND.COM is Not in Root Directory 9. Using INTERLNK and INTERSVR 10. Using TSRs with Network Client 11. Named Pipes and Enhanced Mode Windows 12. Using Qualitas Maximize or Quarterdeck Optimize 13. Using QEMM Lastdrive 14. Making the Pop-up Interface Visible on a Monochrome Monitor 15. Enabling Validated Logons to Windows NT and LAN Manager Domains 16. Network Settings in SYSTEM.INI 17. NWLink Supports IPX Only 18. Installing the MS-DLC Protocol 19. Installing Remote Access Service 1.1a 20. Browsing the Network Requires a Windows for Workgroups or Windows NT Computer on the Network 21. IPCONFIG.EXE and Controlling DHCP Leases 22. Specifying WINS Servers 23. Differences in MS-DOS TCP/IP 24. Logging On With TCP/IP Across a Router 25. Overview of Windows Sockets 26. Setting DNR and Sockets Settings 27. New and update NDIS Drivers ------------------------------------------ 1. Installing Network Client ---------------------------- If you are installing Microsoft Network Client version 3.0 for MS-DOS on a computer that does not have MS-DOS installed, you will get the error "No Drivers Present On This Disk" if you try to use the Windows Driver Library. You must have MS-DOS installed on the computer. If you have a Windows NT Server floppy disk set and you want to make extra copies of Microsoft Network Client for MS-DOS, note that the installation disk for this client will only fit on a 3.5" floppy disk. 2. Setup PATH Problem With Microsoft Windows -------------------------------------------- If you have Microsoft Windows installed on your computer before you install Network Client, the Network Client Setup program may incorrectly alter the PATH line in your AUTOEXEC.BAT file. The PATH line should include the Windows directory. Check this line after you install Network Client. If the Windows directory was removed from the PATH, add it back in. 3. If You Have an 8088 Processor -------------------------------- You must use the basic redirector if your computer has an 8088 processor. The full redirector is the default, so you must choose the basic redirector when you install. 4. Setup Requires 429K Available Memory --------------------------------------- In order to run Network Client Setup, you must have 429K of available conventional memory. 5. Setup is Slow on Some Computers ---------------------------------- On some computers, particularly those with 8088 processors, Network Client Setup may appear to pause for as long as five minutes. Do not restart your computer. 6. Network Client Cannot Be Set Up on DoubleDisk Drive ------------------------------------------------------ You cannot use Network Client on a Vertisoft Systems DoubleDisk drive. You must set up Network Client on another type of drive. 7. Windows 3.x Setup Network Choice ------------------------------------ If you have installed Microsoft Network Client 3.0 and then later install Windows 3.x, the Windows Setup program asks you to choose your network type from a list. "Network Client" does not appear on the list because it is newer than Windows 3.x. Instead, choose "LAN Manager 2.1." 8. If COMMAND.COM is Not in Root Directory ------------------------------------------ Network Client will not start if your COMMAND.COM file is not in the root directory of your startup drive, unless you have a SHELL command in your CONFIG.SYS file that specifies the location of COMMAND.COM. For information about the COMMAND and SHELL commands, see your MS-DOS documentation. 9. Using INTERLNK and INTERSVR ------------------------------ Do not use the MS-DOS INTERLNK or INTERSVR commands with Network Client. 10. Using TSRs with Network Client ---------------------------------- If you start any terminate-and-stay-resident programs (TSRs) and you are using the basic redirector, you might be unable to unload the basic redirector. 11. Named Pipes and Enhanced Mode Windows ----------------------------------------- Asynchronous named pipes are not supported on Microsoft Network Client when the client is running under enhanced mode Windows. All other client APIs are supported, including NetBIOS, TCP/IP, and IPX/SPX. 12. Using Qualitas Maximize or Quarterdeck Optimize --------------------------------------------------- In some rare situations, Qualitas(R) Maximize and Quarterdeck(R) Optimize may attempt to load some Network Client commands into the upper memory area. If this causes problems, use Maximize or Optimize in manual mode and do not use it to load Network Client commands into the upper memory area. Network Client automatically loads its commands into the upper memory area, if there is enough space. For information about using manual mode, see your Maximize or Optimize documentation. 13. Using QEMM Lastdrive ------------------------ If you add drive letters by using QEMM(R) Lastdrive, and then use Network Client to connect to one of them, the connection will be successful but no information about the shared resources on it will be displayed. 14. Making the Pop-up Interface Visible on a Monochrome Monitor --------------------------------------------------------------- To make the Network Client pop-up interface appear in monochrome mode, type MODE MONO at the MS-DOS command prompt before you display the pop-up interface, or include the MODE MONO command in your AUTOEXEC.BAT file. 15. Enabling Validated Logons to Windows NT Server and LAN Manager Domains ------------------------------------------------------------------- You must run the Network Client full redirector to have your user name and password validated by a Microsoft Windows NT Server or LAN Manager server. 16. Network Settings in SYSTEM.INI ---------------------------------- The [Network] section of your SYSTEM.INI file contains the following settings: filesharing= Does not apply to Network Client. printsharing= Does not apply to Network Client. autologon= Determines whether Network Client will automatically prompt you for logon when it starts. computername= The name of your computer. lanroot= The directory in which you installed Network Client. username= The username used by default at logon. workgroup= The workgroup name. Note that this may be different from the "logondomain" setting. reconnect= Determines whether Network Client restores previous connections when it starts. dospophotkey= Determines the key you press (with CTRL+ALT) to start the pop-up interface. The default is N, meaning that you press CTRL+ALT+N. lmlogon= Determines whether Network Client prompts you for a domain logon when you log on. Set this to 1 if you need to log on to a Windows NT Server or LAN Manager domain. logondomain= The name of the Windows NT Server or LAN Manager domain. preferredredir= The redirector that starts by default when you type the NET START command. autostart= If you choose a network adapter during setup, and specify the startup option Run Network Client Logon, autostart determines which redirector you are using. If you select No Network Adapter from the adapter list, or Do Not Run Network Client from the startup options, autostart has no value, but the NET START command still appears in your AUTOEXEC.BAT file. maxconnections= Does not apply to Network Client. 17. NWLink Supports IPX Only ---------------------------- The NWLink protocol shipped with Microsoft Network Client supports only IPX. SPX is not supported. 18. Installing the MS-DLC Protocol ---------------------------------- If you install the MS-DLC protocol, you must edit the AUTOEXEC.BAT file to add "/dynamic" to the NET INITIALIZE line. The line should be: net initialize /dynamic If one does not already exist, add a NETBIND line after all lines in AUTOEXEC.BAT that load network drivers. The line should simply be: netbind 19. Installing Remote Access Service 1.1a ----------------------------------------- To use RAS, you must use the Network Client full redirector. After creating the RAS 1.1a disks, run the Network Client Setup program. Do not use the setup program provided with RAS 1.1a to configure your network settings. 1. In the Network Client directory, run SETUP.EXE. 2. Choose Change Network Settings, and then select Add Adapter. 3. Select Microsoft Remote Network Access Driver from the list of adapters, and then choose The Listed Options Are Correct. 4. After running Setup, run the RASCOPY.BAT batch file. It will prompt you for the Remote Access Service disk 1 and disk 2. To disable remote access, remove Microsoft Remote Network Access Driver from the list of adapters. To re-enable it, follow steps 1 through 3. When the Remote Access files are installed, a RAS directory is created in your Network Client directory. Use the SETUP.EXE program in this directory only to configure your modem, not to configure network settings. In particular, do not select Enable Remote Access or Remove Remote Access when running SETUP.EXE from the RAS directory. 20. Browsing the Network Requires a Windows for Workgroups or Windows NT Computer on the Network ------------------------------------------------------------- Network Client does not provide a browse master. In order for you to browse the network, a browse master must be present. Therefore, a computer running Windows for Workgroups or Windows NT must be on the network and belong to the same workgroup as the computer running Network Client. See the Windows for Workgroups 3.11 Resource Kit for information on making the Windows for Workgroups machine a browse master. Note that this does not prevent you from connecting to a shared resource. You will just need to know the name of the server and share beforehand in order to connect to it. 21. IPCONFIG.EXE and Controlling DHCP Leases -------------------------------------------- The IPCONFIG.EXE utility provides DHCP configuration information. The version of IPCONFIG.EXE provided with the Microsoft Network Client does not support command-line switches for controlling DHCP address leases; you must use the DHCP Administration Utility instead. Specifically, the Network Client IPCONFIG.EXE utility does not support the following switches, which are available in the IPCONFIG.EXE utilities for Windows for Workgroups and for Windows NT: IPCONFIG /release IPCONFIG /renew IPCONFIG /? IPCONFIG /all 22. Specifying WINS Servers --------------------------- If your MS-DOS client uses DHCP (the default setting for MS-DOS TCP/IP), it will automatically receive the address for the WINS server. If you want to statically configure your WINS server IP address, you must edit the client's PROTOCOL.INI file and add the IP address into the [TCPIP] section. For example, if you have 2 WINS servers available, add them into the [TCPIP] section as shown in the example below. Note that there are no dots (.) in the IP addresses. [TCPIP] WINS_SERVER0 = 11 101 13 53 WINS_SERVER1 = 11 101 12 198 Name queries will be sent to the WINS servers in the order in which they appear in the .INI file. The IPCONFIG command may show a different order of WINS servers (or even different WINS servers altogether) -- these are the WINS server names sent by DHCP, and the PROTOCOL.INI settings override them. 23. Differences in MS-DOS TCP/IP -------------------------------- There is a difference in functionality available in TCP/IP for Windows for Workgroups, and Windows NT Workstation and Server, versus MS-DOS TCP/IP. Specifically, an MS-DOS TCP/IP client does not: support DNS resolution using WINS support WINS resolution using DNS register its name with the WINS database; it does queries only act as a WINS proxy node have multihomed support support IGMP 24. Logging On With TCP/IP Across a Router ------------------------------------------ If the domain controller is across a router from the Network Client computer, you must add a line to the client's LMHOSTS file for logons to be validated. The line is of the following form: www.xxx.yyy.zzz SRV_NAME #DOM:DOM_NAME where www.xxx.yyy.zzz is the IP address of the domain controller SRV_NAME is the NetBIOS name of the domain controller DOM_NAME is the name of the domain You must also ensure that the domain controller can contact the client, using one of the following methods: Enter the client's IP address and name in the domain controller's LMHOSTS file. Register the client with a WINS server that is accessible by the domain controller. (Network Client computers do not automatically register with WINS servers; they only query the WINS servers.) Use the LAN Manager 2.1a (and higher) "TCP/IP Extensions for LAN Manager," a hub/node service that runs on LAN Manager servers to integrate domains across routers. 25. Overview of Windows Sockets ------------------------------- Microsoft TCP/IP includes support for Windows Sockets on Microsoft Windows and Workgroups for Windows workstations. A socket provides an end point to a connection; two sockets form a complete path. A socket works as a bi-directional pipe for incoming and outgoing data. The Windows Sockets API is a networking API tailored for use by programmers using the Microsoft Windows operating system. Windows Sockets is a public specification based on Berkeley UNIX sockets and aims to: * Provide a familiar networking API to programmers using Windows or UNIX. * Offer binary compatibility between heterogeneous Windows-based TCP/IP stack and utilities vendors. * Support both connection-oriented and connectionless protocols. If you are running an application that uses Windows Sockets, be sure to enable Windows Sockets when you configure Microsoft TCP/IP. If you are unsure whether any of your applications use Windows Sockets, refer to the documentation included with that vendor's application. 26. Setting DNR and Sockets Settings ------------------------------------ If you specify the MS TCP/IP protocol during setup, you will now see an additional dialog box after you have used the Advanced button in the MS-TCP/IP Configuration dialog box. This new dialog box, DNR and Sockets Settings, is used only if your MS TCP/IP network has a domain name service (DNS) server. If your network has a DNS and you choose to configure the Domain Name Resolver (DNR) parameters, the DNR module will be loaded with your sockets and Telnet applications to resolve hostname-to-IP address mappings. This allows you to specify remote computers by computername without knowing specific IP addresses. If you use this dialog box, these are the values you will need to supply: Username Your username. Hostname The computername your workstation will report when using the remote services. The default is your LAN Manager computername. Primary Nameserver IP Address The IP address of the DNS server you want the DNR to consult first when resolving computername-to-IP address mappings. If you use DHCP, the DHCP server typically provides a DNS server address automatically; you can leave this entry blank. If you do specify an address here, it overrides the address provided by DHCP. Secondary Nameserver IP Address The IP address of the DNS server you want the DNR to consult when resolving computername-to-IP address mappings if the request to the primary nameserver fails. If you use DHCP, the DHCP server typically provides a DNS server address automatically; you can leave this entry blank. If you do specify an address here, it overrides the address provided by DHCP. Domain Name Suffix The suffix appended to any computername for DNS processing. Your network administrator can tell you what to enter here. Enable Windows Sockets Mark this checkbox if you want Sockets to be invoked from the AUTOEXEC.BAT file. Number of Sockets The maximum number of sockets that can be made available to applications at any one time. The range is 1 to 22 sockets. Note: Some applications may use more than one socket to provide a service. Consider this when trying to maximize available memory. The total number of sockets and NetBIOS sessions combined must not exceed 22. 27. These drivers are located in update directory.. (under wdl) ------------------------------------------------------------------ PCNet Ethernet Adapter v 1.1 \clients\wdl\update\pcnet Proteon 1346/47 v 1.0 \clients\wdl\update\protat Intel EtherExpress Pro \clients\wdl\update\EPRO Novel/National/Eagle NE2000 plus \clients\wdl\update\NE2000p SMC Ethercard 8216 series \clients\wdl\update\smc8000 Dec Etherworks 3 \clients\wdl\update\ewrk3 3COM Token Link III \clients\wdl\update\tlnk3 SMC Toekncard Plus (SMC8115T) \clients\wdl\update\smc8100 Racore 16/4, \clients\wdl\update\racore IBM Token Ring II \clients\wdl\update\ibmtok Madge 16/4 Smard Ringnode \clients\wdl\update\madge